DeWalt 10" Jobsite Table Saw w/ Rolling Stand DWE7491RS Reviews

About a decade in, a good portable jobsite saw with a really solid fence, used to build cabinets and picture frames.

Five years in, everything still works; holds true once squared and dialed in, good enough for cabinets and furniture, with the left and right slots slightly off parallel.

Worked it hard for 8 years, then passed it to a friend who still uses it for hobbies; had really good luck with it.

Paid $650 new for this exact saw and loves it.

On their second one after roughly 4-5 years; a daily workhorse for ripping framing lumber.

Going strong for 5 or 6 years and plenty accurate for their work, though not a cabinet saw.

A wonderful saw in their own use, and they consider the asking price a good deal.

Came new in a bundle with an XR drill/driver set, and they like it a lot.

Talked a used one down to $475; after only brief use making a featherboard they are happy with how it feels.

Fitted a soft start module to their saw following posted wiring details and reports it works great.

No loose-blade problem in a year of use and a great saw so far, though others' reports give them pause.

Ended up buying it as a first table saw; with one good planed side it is accurate enough to rip boards for glue-ups.

Previously owned it and found it very stable with no play in the housing, selling it only to get a stiffer top.

Went with it over a Bosch and reports zero regrets after a couple of years, saying it does everything needed and more.

Added a soft start module to their saw and says the wiring instructions worked perfectly; notes the module has an adjustment screw for the softest start.

Everyone who uses their saw loves it; they think the fence problem in the thread is a defective unit.

Four of these in use; the arbor that accepts a dado stack is the biggest perk.

Homeowner and amateur who uses the saw heavily and loves it.

About two years in after a discounted retaped-box purchase, very happy: good power, accurate adjustments and quick setup.

Owner who likes it quite a bit; notes it takes a dado stack, which many small saws cannot, and likes the fence.

Really likes the saw overall, but warns the cast aluminum top is not perfectly flat; the waviness does not seem to matter much in use.

Beginner who bought it on sale and feels it was worth the price; praises the warranty, solid build and especially the easy, accurate rack and pinion fence.

Loves the rack and pinion fence on their own saw.

The rack and pinion fence is the best they have used, and it stayed dead on square six months after they set it.

Handles both job site work and finer work well; long boards and large flat sheets are a challenge because of the saw size.

A job site workhorse they would buy again, though they now use a cabinet saw for shop work; cuts are fine for plywood with a good feed setup.

After owning both a Ridgid jobsite saw and this one, this is much better, mainly for its fence, though the Ridgid stand is nicer.

Chosen for its dado capability with a highly rated fence; the first unit had a blade alignment defect and the maker replaced it under warranty.

Runs a dado stack on it regularly and rips plywood to full width; values the extra rip capacity and says it suits a cramped workshop.

Upgraded from the smaller 8-1/4 inch saw after a year and likes the 10 inch model more, mainly for sharing blades with a miter saw and wider blade choice. Notes both saws are very loud.

About six months of ownership with no regrets. Easy to move and load into a truck, and a dado stack works very well on it after replacing an older saw that died.

Finds the saw with its rolling stand pretty portable, loading it right into a Jeep.

Daily trim work for 13 years before any problem; the rack and pinion fence is top notch.

Nearly every day for six years, super accurate for its class; no upgrade planned until they can afford a cabinet saw.

Recently bought as a first table saw; likes the slick rack and pinion fence, adjustability, easy blade changes and dado capability, though not enough use for a strong opinion yet.

Worked on many job sites with units from brand new to heavily abused, and judged clearly better than a Bosch alternative, with a standout fence system.

Stable on grass, sand and concrete, with an easy fence; wishes for more rip capacity and a longer arbor, and plans to keep it even after buying a cabinet saw.

Recently bought after giving up on a sale, as an upgrade from an older 20 inch jobsite saw. Builds a few sets of kitchen cabinets a year, and calls the saw absolutely worth it, with dado ripping now possible.

A favorite that they love, crediting the rack and pinion fence and the weight; advises keeping the gearing clean since that wears first on jobsite saws.